Signal range
The point-to-point indoor range is ± 10 m. In open spaces, the RF range reaches 30 m. The meshing capability of 230 V powered Zigbee® devices can extend the RF range.
For more information see Zigbee® network principle.
The maximum point-to-point RF range of the connected switch to a Zigbee® receiver depends on:
-
The materials used in the building or room,
-
The indoor position of the connected switch, Zigbee®, and
-
Sources of interference.
Materials and obstructions
Radio waves can be attenuated by materials inside a building or room.
|
|
|
|
|
|
Wood, plaster, uncoated, without metal |
Brick, concrete |
Ferroconcrete, lightweight hollow walls filled with insulating wool on metal foil, metallic heating insulation sheets, metallic surfaces, glass with a metal coating, floor heating systems, metal faceplates |
Confined metal space |
|
Loss: 5-20% |
Loss: 20-40% |
Loss: 40-90% |
Loss: 90-100% |
A human body can obstruct the Zigbee® radio path since its operating frequency band (2.4 GHz) resonates well with water particles. The Zigbee® meshing capability will generally remain intact after a radio path distortion, but take caution when a lot of people, or an object containing large volumes of water (e.g. an aquarium), are located in a room.
Position
Avoid installing the Zigbee® device:
-
In a narrow room with thick walls,
-
On the same wall as another Zigbee® repeating or receiving node,
-
Close to the ground (the recommended mounting height is 110 cm),
-
On a metal or moist surface or in a damp environment, or
-
In so-called 'dead spots', caused by radio reflections from nearby conductive materials or obstacles such as, metal cupboards, doors with a metallic foil or items containing water (e.g. aquariums).
Sources of interference
A Zigbee® connected switch is generally not disrupted by low-power electronic devices (e.g. DECT telephones, smartphones, WLAN routers, analogue radios, electronic ballasts, controllers, TVs, videos, computers, remote controls), and vice versa. Zigbee® is a robust and reliable RF technology thanks to its meshing capability and ability to capture radio telegrams from noisy environments.
Mind that a high-power electronic device in a room may interfere with the radio telegrams of a connected switch. Should this occur, identify the interfering source and remove it. If removal is not possible, consider relocating the connected switch or add a Zigbee® repeating node (e.g. a 230 V powered Niko Zigbee® device).
Wiring scheme
Switch off the mains.
|
Manual use |
Connected use |
|---|---|
|
This product must be secured with a miniature circuit breaker (MCB) of max. 16 A in the electrical cabinet. The MCB rating is limited by national installation rules |
This product must be secured with a miniature circuit breaker (MCB) of max. 16 A in the electrical cabinet. The MCB rating is limited by national installation rules |
-
All mechanical push-button extensions wired to the same terminal, will show the same behaviour (either the standard behaviour of the actor or a programmed behaviour). It is not possible to configure the behaviour of these extension switches separately. The maximum total wire length for all extension buttons connected to the Zigbee® switch is 50 m.
-
Also respect a minimum distance of 2 m between a Zigbee device (including the smart hub) and another RF transmitter (for example a Wi-Fi device) or devices such as motors, pumps, electronic LED transformers, solar panel inverters, home battery storage ...
Installation of the connected single switch, Swiss line
Note that the installation of a flush-mounting box and the electrical wiring is required prior to installing the connected Zigbee® device. For more information, check the Specifications on Connected single switch, Zigbee®, 10 A, Swiss line.
To install the connected single switch, proceed as follows:
Switch off the mains.
|
Step |
Action |
|---|---|
|
|
|
|
|
|
|
|
|
|
|
|
-
The connected switch only switches the L-wire towards its pole contact. The N-wire will not be switched