Bulex

What can you do with Niko Home Control?

By using Niko Home Control with your Bulex system, you can do the following:

	Connected systems supported by
	MiGo app	MiGo Link app
Check and control the room temperature (one zone)
Check and control the room temperature (more zones)
Check the outside temperature
Choose the heating program mode (home, away)
Choose the operation mode (summer, winter, frost guard)
Check and boost the temperature of the hot water system (*)
Choose the heating program mode (off, manual, schedule, away, boost) (*)

(*) Boost is only available for domestic hot water.

The Bulex functions automatically appear in your Niko Home app and on your touchscreen after you activate the link between both systems. To control the Bulex functions on your Digital bIack, select the Bulex controls for your Digital black in the Niko Home app. The functions can also be combined in routines to control multiple items simultaneously at the simple press of a button.

The available functionality within Niko Home Control depends upon the specific installation features of the Bulex system.
You can always use the MiGo app or MiGo Link app for more advanced settings and configurations.

What do you need?

In short

Extra information

General

No additional electrical wiring is required.
You have a computer with a web browser and an internet connection to set up the link between both systems.

Your Niko Home Control installation meets the following requirements:

It has a wireless smart hub or a connected controller.
It is configured with the most recent programming software (version 2.17 or higher).
It has an active internet connection.
It is registered.
You have your Niko Home Control installation e-mail address and password on hand.
If you want to use the Bulex functions in combination with Niko Home Control routines, these routines need to be programmed with the Niko Home Control programming software after the link has been activated.

If you have not registered your Niko Home Control installation, go to mynikohomecontrol.niko.eu.

Your Bulex system meets the following requirements:

It is a Bulex boiler/heat pump having a Bulex communication unit.
It has one of the following thermostats:
- thermostat supported by the MiGo app
- thermostat supported by the MiGo Link app.
It has an active internet connection.
You have the serial number of the communication unit on hand.

You can find the serial number of the communication unit:

on the backside or the inside of the unit below the barcode
in the MiGo app or MiGo Link app

How do you activate the link between your Niko Home Control and your Bulex system?

If you only want to control your partner system with the Niko Home app, a touchscreen or a Digital Black activating the connected service in the Niko Home Control programming software suffices.

Check if you have everything you need (see above).
Activate the Bulex connected service in the Dashboard menu. Doing this, you already can control your Bulex system via the Niko Home app and a touchscreen. To control the Bulex functions on your Digital bIack, select the Bulex controls for your Digital black in the Niko Home app.
If you want to use your Bulex system as a part of your configuration (use the system in routines and/or conditions), follow the additional steps below.
Add one or both of the following devices:
- generic heating Bulex
- generic warm water Bulex
Create the desired routines and/or conditions with the Bulex device(s).
Address the Bulex devices.
Upload the configuration file to your installation.

How do you deactivate the link between your Niko Home Control and your Bulex system?

Deactivate the Bulex connected service in the Dashboard menu.
If you used your Bulex system as a part of your configuration (used the system in routines and/or conditions), follow the additional steps below.
Remove the generic heating Bulex device and/or generic warm water Bulex device from the floor plan.
Upload the configuration file to your installation.

After deactivating the link, the following happens:

The Bulex functions disappear from your Niko Home app, your touchscreen and your Digital black.
When used in Niko Home Control routines, the Bulex functions will not be executed anymore.