Description
The DALI-2 fully addressable 2-channel interface module allows up to 128 DALI endpoints to be connected to a Niko Home Control installation. Addressing and programming of the DALI devices is done from within the Niko Home Control programming software, and no prior DALI knowledge is required. Each of the DALI endpoints can be configured and controlled separately, without the need to use any other DALI software or interface. The module comes with a built-in power supply, so there is no need to use a dedicated DALI power supply for the DALI bus.
OVERVIEW
|
550-00370 |
Control
Technical data
DIMENSIONS IN MM
SPECIFICATIONS
Specification | Value |
|---|---|
Article number | 550-00370 |
| Input voltage | 230 Vac (± 10%), 50 Hz |
| Wire capacity | 2 x 1.5 mm² / 2 x 2.5 mm² / 1 x 4 mm² |
| Mounting method | DIN rail |
| Maximum power consumption | 11 W |
| Power consumption (standby) | 1.9 W |
| Power supply | built-in DALI power supply |
| DALI protocol | EN62386 |
| Supported DALI devices | DALI control gear DT0 to DT7 |
| DALI transmission rate | 1200 bit/s |
| DALI output voltage | 12 - 20.5 V |
| Maximum number of DALI outputs per channel | 64 |
| Maximum output current per channel | 250 mA |
| Maximum guaranteed current per channel | 175 mA |
| Dimming | absolute and relative |
| Protection | short-circuit, surge voltage, overload |
| DALI short circuit | retry mechanism |
| Configuration | Niko Home Control programming software |
| Control | Niko Home Control II app / Niko Home app |
| System compatibility | Niko Home Control II |
| Weight | 137 g |
| Ambient temperature | 0 - 45 °C |
| Dimensions (HxWxD) (mechanism) | 90 x 70 x 67 mm (DIN U4) |
| Protection degree | IP20 |
| Marking | CE |
Supported DALI control gear
The table below shows the supported DALI control gear in Niko Home Control II.
| Part | Type of control gear | Device type number |
|---|---|---|
| 201 | Fluorescent, lamp control gear | Device Type 0 (DT0) |
| 202 | Self-contained emergency, control gear | Device Type 1 (DT1) |
| 203 | Discharge HID, lamp control gear | Device Type 2 (DT2) |
| 204 | Low-voltage halogen, lamp control gear | Device Type 3 (DT3) |
| 205 | Incandescent lamp, dimmer | Device Type 4 (DT4) |
| 206 | Conversion to DC voltage (1 - 10 V, 0 - 10 V converter) | Device Type 5 (DT5) |
| 207 | LED lamp, control gear | Device Type 6 (DT6) |
| 208 | Switching, relay control gear | Device Type 7 (DT7) |
Device type 8 (colour control gear) is not yet supported in Niko Home Control II.
Note: Colour control is enabled with DALI-2 addressable modules for Niko Home Control in a lighting network containing LED drivers that support an operating mode with dual DALI addresses.
The DALI-2 addressable module for Niko Home Control will detect LED drivers with a dual DALI addressing mode as two separate DALI devices.
One DALI address can then be configured to change the light intensity, and the other DALI address can be used to configure the colour or colour temperature.
Examples of LED drivers that support dual DALI addressing include the products from Lunatone with operating modes Balance & Dim or Colour & Dim.
Supported DALI control devices
DALI control devices are not supported in Niko Home Control II.